StencilCoat™
If stamped asphalt is a revolution in decorative paving systems, StencilCoat™ is the evolution. With StencilCoat™ you can have the look and longevity of real stone or brick for a fraction of the cost. And StencilCoat™ will bond to both concrete and asphalt surfaces.
Where can you use StencilCoat™? Driveways, walkways, patios, pool decks, garage slabs, pedestrian walkways, embankments, outdoor plazas, courtyards, building entrances, theme parks, golf cart paths, and more...just wait until you see the results!
The “StencilCoat™ Commercial Asphalt Coating” is a 100% acrylic waterborne coating system applied to a stamped asphalt or concrete surface.
StencilCoat™ is a three step coating system consisting of:
1. Primer
2. Base Coat
3. Top Coats
StencilCoat™ coatings can be applied to new as well as existing asphalt or concrete surfaces, and is ideal for crosswalks or sidewalks. It can be applied to renew spalled concrete sidewalks and curbs, with or without pattern, or to dress up existing sidewalks with patterns and to provide slip resistance.
StencilCoat™ is currently available in the following colors:
 Brick Red |
 Sierra |
 Chocolate |
 Safety Green |
 Old Brick |
 Sandstone |
 Charcoal |
 School Zone Green |
 White |
 Yellow |
 Taupe |
 Sunset Blush |
 Bedrock |
 Irish Cream |
 Terra Cotta |
 Slate |
 Khaki |
 Burnt Sienna |
 Natural Cement |
 San Diego Buff |
 Desert Buff |
 Nutmeg |
 Fawn |
 Granite |
 Pewter |
 Forest Green |
 Safety Blue |
StencilCoat™ Commercial Asphalt Coating (Tint Base)
Material Composition
Table 1
Characteristics |
Requirement |
|---|---|
Resin ............. |
waterborne latex |
% Solids by weight ............. |
> 80% |
% Solids by volume ............. |
> 65% |
Weight per gallon ............. |
13.5 lbs/gal |
% non-reactive fillers ............. |
< 40% |
Volatile Organic Compounds ............. |
< 75 g/l or 1/4lb/gal |
Boiling Range ............. |
147° - 477°F |
Vapor Density ............. |
Heavier than air |
Liquid Density ............. |
1.5 – 1.7 kg/l @ 20°C |
Flashpoint ASTM D 3278 ............. |
>201°F |
Hazardous Ingredients ............. |
none |
Viscosity @ 70°F (20°C) ............. |
100-110 kU |
Mix Ratio (Coating : LiquidTint) gal/pints ...…........ |
5gal : 1pint |
Dry mil thickness per coat ............. |
20 to 25 mils |
Number of coats to achieve rec. thickness ............ |
3 coats |
Performance Requirements
Table 2
Test |
Requirement |
|---|---|
Dry Time (to re-coat) @ 50°F (10°C)............. |
50 min |
Dry Time (to re-coat) @ 90°F (32°C)............. |
30 min |
85% Cure (to permit traffic) @ 50°F (10°C)............. |
6 to 8 hours |
85% Cure (to permit traffic) @ 90°F (32°C)............. |
2 to 4 hours |
ASTM 2486 Scrub Resistance (30 dry mils).............. Applied as per manufacturers specifications……………… |
5000 cycles to max loss of 50% coating thickness |
Dry mil build thickness per coat ............. |
20 to 25 mils |
Temp. limits for service (of cured material) ............. |
-35°F to 145°F |
Friction using a locked wheeled tester at 30 mph ........... |
>45 FN30R |
Friction using a locked wheeled tester at 30 mph ........... |
>40 FN30R |
Pedestrian Friction ASTM E303 British Pendulum.........…. |
>70 BPN
|
Primer/Sealer (used as a base primer as well as a top sealer where anti-skid is not required) Primer/Sealer is water based 100% acrylic waterborne
Material Composition
Table 3
Characteristics |
Requirement |
|---|---|
Resin ............. |
waterborne latex |
% Solids by weight ............. |
> 30% |
% Solids by volume ............. |
> 29% |
Weight per gallon ............. |
8.5 lbs/gal |
% non-reactive fillers ............. |
< 0% |
Volatile Organic Compounds ............. |
< 45 g/l or 1/10lb/gal |
Boiling Range ............. |
147° - 477°F |
Vapor Density ............. |
Heavier than air |
Liquid Density ............. |
??? Ron, need info ??? |
Flashpoint ASTM D 3278 ............. |
>201°F |
Hazardous Ingredients ............. |
none |
Viscosity @ 70°F (20°C) ............. |
44> kU |
Mix Ratio (Primer : Water) ...…........ |
1 primer : 1 water |
Mix Ratio (Sealer : Water) ...…........ |
1 sealer : 2 water |
Dry mil thickness per coat ............. |
1 to 2 mils |
# of primer coats to achieve rec. thickness ............ |
1 coat |
# of sealer coats to achieve rec. thickness ............ |
1 coat |
Performance Requirements
Table 4
Test |
Requirement |
|---|---|
Dry Time (to re-coat) @ 50°F (10°C)............. |
50 min |
Dry Time (to re-coat) @ 90°F (32°C)............. |
30 min |
85% Cure (to permit traffic) @ 50°F (10°C)............. |
6 to 8 hours |
85% Cure (to permit traffic) @ 90°F (32°C)............. |
2 to 4 hours |
ASTM 2486 Scrub Resistance (3 wet mils)............. |
500 cycles |
Dry mil build thickness per coat ............. |
1 to 2 mils |
Temp. limits for service (of cured material)............. |
-35°F to 145°F |